Vacuum pump datasheets throw a lot of units and terms at you — CFM, m³/hr, Torr, mbar, absolute pressure, ultimate vacuum — and it’s easy to nod along without a working sense of what each one actually tells you about whether a pump will do the job. That gap causes real problems: a pump that looks correctly sized on paper but doesn’t perform, or a spec conversation with a supplier where two sides are technically talking past each other.

This is a working reference — enough to read a datasheet with confidence and ask the right questions during sizing, without turning it into a physics lecture.

Pressure Units: Torr, mbar, and Why There Are So Many

Vacuum pressure is measured in several different unit systems, mostly for historical and regional reasons, and datasheets don’t always agree on which one to use.

  • Torr — Based on millimeters of mercury (1 Torr ≈ 1 mmHg). Common in pumps of European and American origin, and very common in vacuum literature generally. Atmospheric pressure is about 760 Torr.
  • mbar (millibar) — Common on European equipment and increasingly standard in Indian industrial specifications. Atmospheric pressure is about 1013 mbar.
  • kPa / Pa — SI pressure units, used more in scientific contexts and increasingly on modern datasheets alongside the traditional units. Atmospheric pressure is about 101.3 kPa.
  • Inches of Mercury (inHg) or mmHg — Common in some American and legacy equipment, especially older gauges.

The practical point: these are all just different scales measuring the same physical quantity — how far below atmospheric pressure you are. When comparing pumps from different suppliers, convert everything to one unit before comparing numbers, and always check whether the figure quoted is absolute pressure or vacuum (below atmosphere) — mixing the two up is a common source of sizing confusion.

Rough conversion reference:

  • Atmospheric pressure ≈ 760 Torr ≈ 1013 mbar ≈ 101.3 kPa
  • A “deep vacuum” duty point (e.g., 5 Torr) ≈ about 6.7 mbar ≈ about 0.67 kPa

Absolute Pressure vs. Vacuum (Gauge) Reading

This trips up more engineers than it should. Absolute pressure is measured from a true zero (a perfect vacuum). Vacuum gauge readings, by contrast, are often expressed as “how far below atmosphere” you are.

When a process spec says “pull down to 50 mbar,” it almost always means 50 mbar absolute — not 50 mbar below atmosphere. Confusing the two leads to a pump being specified for the wrong duty point entirely, sometimes by an order of magnitude. When in doubt, always confirm whether a quoted figure is absolute pressure or a differential/gauge reading, and get it in writing on the process spec sheet.

CFM, m³/hr, and Pumping Speed

CFM (cubic feet per minute) and m³/hr (cubic meters per hour) both describe pumping speed — the volumetric flow rate of gas the pump can move. This is the number most engineers focus on first, but it comes with an important catch: pumping speed isn’t constant across the pump’s operating range.

A pump’s rated CFM or m³/hr figure is usually quoted at or near atmospheric pressure. As the system approaches deeper vacuum, actual pumping speed typically drops — sometimes significantly — because there’s simply less gas mass available to move per unit volume. This is why a pump chosen purely on its atmospheric CFM rating can disappoint once the process gets close to its target vacuum level; what matters for cycle time and hold performance is the pumping speed at your actual operating vacuum, not the headline number at atmosphere.

Practical implication: always ask for (or plot from the pump curve) the pumping speed at your specific target vacuum level, not just the nameplate CFM. This single check catches a large share of sizing mismatches before they become commissioning problems.

Ultimate Vacuum

Ultimate vacuum is the deepest vacuum level a pump can theoretically reach, typically quoted with no process load — essentially the pump running against a sealed, leak-free system with no gas load to remove. It’s a useful ceiling reference, but it is not the vacuum level you should expect under real operating conditions.

Real systems have leakage, outgassing, and — critically for liquid ring pumps — a seal liquid vapor pressure limit that sits well above the pump’s theoretical ultimate vacuum in many cases. Treat ultimate vacuum as “the best this pump can ever do under ideal conditions,” and size against your actual expected operating vacuum with realistic margin, not against the ultimate vacuum figure.

Vapor Load and Why It’s Not Just About Air

Datasheet pumping speed figures are usually based on dry air. If your process involves solvent vapor, water vapor, or other condensables, the effective load on the pump is higher than the equivalent dry-air volume would suggest, because:

  • Condensable vapors add to the total gas load the pump has to move
  • For liquid ring pumps specifically, vapor can affect the seal liquid’s own vapor pressure behavior at the ring interface
  • Vapor composition changes through a batch (as covered in our solvent recovery mistakes guide), so peak load — not average load — is what should drive sizing

Practical implication: a pump sized purely on air-equivalent CFM for a solvent-heavy process is a common way to end up under-delivering on vacuum during peak vapor generation, even though the pump “checks out” against a simple air-based spec.

Suction Capacity Curves — Read the Curve, Not Just the Headline Number

Most reputable pump manufacturers publish a suction capacity curve — pumping speed plotted against operating pressure — rather than a single number. This curve is the single most useful piece of information on a datasheet, because it tells you exactly what the pump will actually deliver at your process’s real operating point, not just at atmosphere or at ultimate vacuum.

When comparing two pumps, don’t compare headline CFM figures side by side — overlay the curves at your actual target vacuum level and compare pumping speed there. Two pumps with identical nameplate CFM can perform very differently at a deep vacuum duty point.

A Quick Reference Glossary

TermWhat It Means
Torr / mmHgPressure unit; 760 Torr = atmospheric pressure
mbarPressure unit; 1013 mbar = atmospheric pressure
Absolute pressurePressure measured from true zero (perfect vacuum)
CFM / m³/hrVolumetric pumping speed — check at your operating point, not just at atmosphere
Ultimate vacuumTheoretical deepest vacuum with no process load — a ceiling, not an operating expectation
Suction capacity curvePumping speed plotted against pressure — the most useful sizing reference on a datasheet
Vapor loadAdditional gas load from condensable vapors, beyond dry-air equivalent
Seal liquid vapor pressureFor liquid ring pumps, sets the practical vacuum ceiling based on seal liquid temperature

Why This Matters When You’re Actually Sizing a Pump

Every one of these terms shows up somewhere in the sizing conversation, and getting even one of them wrong — absolute vs. gauge pressure, headline CFM vs. speed-at-operating-point, ultimate vacuum vs. realistic operating vacuum — can lead to a pump that looks right on paper and underperforms in the plant. The fix isn’t memorizing definitions; it’s knowing which number to actually ask for and at which operating point, before a purchase order gets cut.

If you’re working through a sizing exercise and want a second set of eyes on the numbers — actual vapor load, target vacuum level, and seal liquid conditions — we’re happy to walk through it with you.


JOYAM Engineers & Consultants Pvt. Ltd. manufactures liquid ring vacuum pumps (TS Series, MV Series), dry claw vacuum pumps, Roots vacuum boosters (JRB Series), centralised vacuum systems, and custom solvent recovery systems. Contact us to discuss sizing for your application.